como reprogramar el control remoto

gines luis

Nuevo Forero
La llave de mi coche ha dejado de funcionar como mando a distancia. Le he cambiado la pila y cuando le pulso se enciende una luz roja y no funciona
 

M6 MK1 143D

Forero Activo
SALUDOS, TE MANDO ESTO COPIADO DE UNA WEB..:

Buenas compañero, yo me compré una llave por ebay de 2ª mano y la programé yo mismo el mando a distancia y el transponder que es tu caso, eso sí bajo tu responsabilidad si algo sale mal... pero en fin si sale algo mal pagas lo que cuesta y punto.
Mi mazda 3 es del 2004 y me traia dos llaves como la que pones y los mandos aparte. Me compré una llave con todo incluido y tuve que programar las dos cosas.
Te paso un link donde aparecen las instrucciones, lo primero es sólo para el mando y la segunda para el chip de la llave, para la llave necesitas tener dos llaves operativas para poder programar una tercera.

http://www.mazdas247.com/forum/showthre ... and-Remote

NOTE: this is only for switchblade style and seperate key/remote fob only. Will not work with credit card type keys/remote.

1. Remote programming instructions[/b]

Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!



Key Programming Instructions

The timing is critical to this procedure, please read through the entire procedure before attempting.
Procedure:
1. Insert one of the pre-programmed transponder keys and turn the ignition to "on", leave on for at least one second (I wait until the red key symbol in the instrument cluster extiinguishes), remove the key from the ignition.
2. Within 5 seconds insert the second pre-programmed key and turn the ignition to "on" for at least one second but no more than 5 seconds (use the key symbol for this as well) then remove the second key.
3. within 10 seconds insert the new key in the ignition and turn the ignition to "on", if you are successful the red key symbol will illuminate then extinguish after about a second.

If you are not successful the red key symbol will flash repeatedly to indicate that you have inserted an invalid key. Remove the key, wait a minute and try it again, it took me a few times to get it perfect and I had done it before.
 

M6 MK1 143D

Forero Activo
ESTO OTRO TB ES COPIADO Y EN CRISTIANO...::

Como la mayoría de los coches modernos, el Mazda 6 tiene un mando a distancia para entrar en el coche. Puede que tenga que programar la llave cuando te lo primero que el coche si es nuevo. Usted también puede tener que programar la tecla si ha sustituido la batería, ya que esto puede causar que la clave ya no se sincronizarán con el coche. La clave de control remoto o mando se comunica con el sistema de ordenador de a bordo de su coche para abrir la puerta. Es posible programar la llave sí mismo sin tener que visitar su concesionario Mazda. Cosas que necesitará
Mazda 6 teclas

Ver Más instrucciones

1 Abra la puerta del lado del conductor y sentarse en el coche con la puerta abierta.

2 Pulse el botón "lock" en el interior de la puerta. Pulse desbloquear inmediatamente después.

3 Introducir la llave en el encendido. Gire la llave a la posición "On", y luego de nuevo. Repita el proceso tres veces en 10 segundos.

4 Cierre la puerta del coche y abrir de nuevo. Repita el proceso dos veces más para que lo haga con un total de tres veces. En la tercera vez que la puerta debe estar abierta. Las puertas se bloquearán y desbloquearán automáticamente.

5 Pulse el botón de bloqueo del mando a distancia dos veces rápidamente. Las puertas se bloquearán y desbloquear a medida que presiona el botón.

6 Sal del coche y cerrar la puerta. Pruebe la tecla pulsando bloqueo y desbloqueo de nuevo.

Ahora ha programado la tecla 6 Mazda.
 

gines luis

Nuevo Forero
Muchas gracias lo he privado pero no me funciona. Mi llave es de las que lleva el mando incorporado, lo digo por si conocéis alguna otra solución
 

Sidewinder

Forero Activo
Vehículo/s
Mazda 6 2.2d SW 150CV Snowflake white pearl Style Safety + Nav
Creo que lei en algún sitio que había que acercarla al botón start y accionarla. Por probar no pierdes nada.
 
Arriba